详细介绍
不锈钢岗亭焊接反面焊缝时，除重要结构外，不必清根，但要将岗亭骨架正面焊缝背部的熔渣清除干净，然后再焊接，焊接电流大些，以**根部焊透。
V形坡口对接平焊，当不锈钢岗亭的钢板厚超过6MM时，为了**焊透，必须开V形坡口或X形坡口，需采用多层焊或多层多道焊，焊道分布及焊接顺序。多层焊时，焊接岗亭的**层应选直径较小的焊条，使电弧能深入到坡口的根部，运条方法应根据焊条直径
与坡口间隙决定，可采用直线运条或锯齿形运条法，尽可能使根部焊透。
焊接填充层时，可改用直径较粗的焊条和较大的焊接电流施焊，务必使坡口两侧熔合好，每层焊道表面平整，两侧稍下凹，决不能上凸或咬边。
材料清单：
1、骨架：10毫米*100毫米*2.5毫米、80毫米*80毫米*2.0毫米厚热镀锌方管
2、玻璃：钢化单层灰玻
3、铝合金移窗+下面百叶或者镀锌封板
4、吊顶：优质铝塑扣板吊顶或集成吊顶
5、有框门(40*80*2.0毫米厚热镀锌方管）
6、工作台（免漆板）
7、地板：水泥板+SPC地板
8、油漆：富锌环氧底漆2遍、金属面漆2遍
9、吸顶节能灯
10、内部电源控制盒
When the stainless steel pavilion welds the reverse weld, it is not necessary to clear the roots except for the important structure, but it is necessary to clear the slag on the back of the front weld of the pavilion skeleton, and then weld it again, and the welding current is higher to ensure that the roots are soldered.
V-shaped slope butt flat welding. When the steel plate thickness of the stainless steel pavilion exceeds 6MM, in order to ensure welding, the V-shaped slope or X-shaped slope must be opened. Multilayer welding or multi-layer multi-channel welding is required, and the weld is distributed. And welding order. When multi-layer welding, the first layer of the welding booth should be selected with a smaller diameter welding rod, so that the arc can penetrate into the root of the slope, and the rod method should be based on the diameter of the welding rod.
In accordance with the clearance of the slope, the straight or zigzag rod method can be used to weld the roots as far as possible.
When welding the filling layer, you can use a larger diameter welding rod and a larger welding current to weld. Make sure that the sides of the slope are fused well. The surface of each layer of the weld is flat and the sides are slightly concave. You must not bump or bite.
List of materials:
1, skeleton: 10 毫米 * 100 毫米* 2.5 毫米, 80 毫米 * 80 毫米* 2.0毫米thick hot galvanized tube
2, glass: tempered single layer gray glass.
3, aluminum alloy window shift + bottom one hundred leaf or galvanized seal
4, hanging : high-quality aluminum buckle board hanging or integrated hanging
5, framed door(40 * 80 * 2.0 毫米 thick hot galvanized square tube)
6, workbench(paint free board)
7, the floor: cement plate + SPC floor
8, paint: Zinc-rich epoxy primer 2 times, metal paint 2 times
9, suction energy-saving lights
10, internal power control box
V形坡口对接平焊，当不锈钢岗亭的钢板厚超过6MM时，为了**焊透，必须开V形坡口或X形坡口，需采用多层焊或多层多道焊，焊道分布及焊接顺序。多层焊时，焊接岗亭的**层应选直径较小的焊条，使电弧能深入到坡口的根部，运条方法应根据焊条直径
与坡口间隙决定，可采用直线运条或锯齿形运条法，尽可能使根部焊透。
焊接填充层时，可改用直径较粗的焊条和较大的焊接电流施焊，务必使坡口两侧熔合好，每层焊道表面平整，两侧稍下凹，决不能上凸或咬边。
材料清单：
1、骨架：10毫米*100毫米*2.5毫米、80毫米*80毫米*2.0毫米厚热镀锌方管
2、玻璃：钢化单层灰玻
3、铝合金移窗+下面百叶或者镀锌封板
4、吊顶：优质铝塑扣板吊顶或集成吊顶
5、有框门(40*80*2.0毫米厚热镀锌方管）
6、工作台（免漆板）
7、地板：水泥板+SPC地板
8、油漆：富锌环氧底漆2遍、金属面漆2遍
9、吸顶节能灯
10、内部电源控制盒
When the stainless steel pavilion welds the reverse weld, it is not necessary to clear the roots except for the important structure, but it is necessary to clear the slag on the back of the front weld of the pavilion skeleton, and then weld it again, and the welding current is higher to ensure that the roots are soldered.
V-shaped slope butt flat welding. When the steel plate thickness of the stainless steel pavilion exceeds 6MM, in order to ensure welding, the V-shaped slope or X-shaped slope must be opened. Multilayer welding or multi-layer multi-channel welding is required, and the weld is distributed. And welding order. When multi-layer welding, the first layer of the welding booth should be selected with a smaller diameter welding rod, so that the arc can penetrate into the root of the slope, and the rod method should be based on the diameter of the welding rod.
In accordance with the clearance of the slope, the straight or zigzag rod method can be used to weld the roots as far as possible.
When welding the filling layer, you can use a larger diameter welding rod and a larger welding current to weld. Make sure that the sides of the slope are fused well. The surface of each layer of the weld is flat and the sides are slightly concave. You must not bump or bite.
List of materials:
1, skeleton: 10 毫米 * 100 毫米* 2.5 毫米, 80 毫米 * 80 毫米* 2.0毫米thick hot galvanized tube
2, glass: tempered single layer gray glass.
3, aluminum alloy window shift + bottom one hundred leaf or galvanized seal
4, hanging : high-quality aluminum buckle board hanging or integrated hanging
5, framed door(40 * 80 * 2.0 毫米 thick hot galvanized square tube)
6, workbench(paint free board)
7, the floor: cement plate + SPC floor
8, paint: Zinc-rich epoxy primer 2 times, metal paint 2 times
9, suction energy-saving lights
10, internal power control box
联系方式
|
